The manual will provide you with the precise measurements, which must be followed carefully to maintain the integrity and functionality of the lift.
After ensuring the towers are spaced appropriately, we move on to the next phase, which involves drilling holes into the concrete slab to secure the anchors. To do this, you will need to use a masonry bit, specifically designed for this purpose, along with a hammer drill. It’s crucial to drill through the base plate holes and penetrate the concrete until you reach the dirt below the slab. Once you’ve drilled the first hole, you need to clean out the dust and debris from the hole. This can be done with an air blow gun, or alternatively, a shop vacuum can also be used to clear the hole. At this stage, it’s important not to drill the second hole just yet.
Now, there’s an optional step that can be taken to enhance the strength of the Mobile Column Lift For Sale Oceanside CA anchors. While this step is not mandatory, it’s highly recommended to use an adhesive to help ensure the anchors stay securely in place over time. If you decide not to use an adhesive, you can skip this part, but the additional security it provides is worth considering. The adhesive recommended for this purpose is AC100+Gold, a two-part epoxy that should be applied to the expanding end of each anchor before driving it into the hole. It’s important not to mix the adhesive prematurely, as its working time can be quite short, especially in warmer climates, where it can be less than a minute. Timing is critical, so it’s vital to be well-prepared.
To begin applying the Mobile Column Lift For Sale Oceanside CA adhesive, first install the washer, lock washer, and nut onto the anchor. The nut should only be loosely threaded onto the end of the anchor, making sure it is flush with the anchor’s end. This is important because it helps prevent the nut from getting stuck due to the anchor expanding too much during the hammering process. After the anchor is prepared, spread the mixed epoxy on the expanding end of the anchor. Then, proceed to hammer the anchor into the hole until it can’t go any deeper. The goal is to insert the anchor as far as possible into the hole, ensuring that the adhesive will bond it securely.
Once the anchor is in place, it’s essential to tighten it with a wrench. This step expands the anchor inside the hole, ensuring it’s securely held by both the Mobile Column Lift For Sale Oceanside CA adhesive and the mechanical action of the expanding anchor. This is a critical step in the process, as the anchor must be tightened while the adhesive is still wet. If you wait too long and allow the adhesive to cure before tightening the anchor, the adhesive will essentially glue the anchor closed, preventing it from expanding properly. Therefore, it’s crucial to follow the manual’s instructions carefully and tighten each anchor to the specified torque before the adhesive sets. Only once the first anchor is installed and tightened can you move on to the second anchor.
When installing the second anchor, make sure it’s positioned opposite the first one. This ensures proper alignment and prevents any issues later on. Once the second Mobile Column Lift For Sale Oceanside CA anchor is fully installed, you can proceed with installing the remaining anchors. It’s important not to rush and try to install all the anchors at once. Following the sequence described ensures that the anchors align properly with the holes in the concrete and prevents issues such as misalignment. The anchors need to be installed one at a time, starting with the first two, which set the foundation for the rest. Using this method will prevent the situation where you’ve drilled all the holes and installed some anchors, only to discover that the remaining ones no longer align with the holes.
One additional piece of advice is to avoid using an impact wrench when tightening the anchors. An impact wrench can cause uneven torque, which could lead to issues with the anchors not being fully tightened or expanded correctly. It’s essential to use a standard wrench to achieve the proper torque specified by the manufacturer. By taking your time, ensuring everything is aligned correctly, and following each step in the right order, you’ll ensure that the lift is securely installed and ready for use.
This process involves several meticulous steps, each of which plays a critical role in ensuring the lift functions safely and securely. From properly aligning the towers to drilling the holes, using the right adhesive, and ensuring each anchor is installed and torqued correctly, the installation of the lift is a precise and detailed task that requires patience and attention to detail. By following these steps carefully, you can be confident that your Mobile Column Lift For Sale Oceanside CA lift will be safely and securely anchored, providing reliable service for years to come.
After securing the first Mobile Column Lift For Sale Oceanside CA tower to the concrete foundation, it is essential to wait the specified duration recommended for the adhesive to fully cure, as indicated on the adhesive tube. This curing period ensures the adhesive reaches its optimal strength before any further adjustments are made. During this waiting period, it is a good idea to prepare for the next step, which involves installing the shims that come with the lift. The purpose of these shims is to make sure the tower is perfectly plumb. Achieving a plumb position means the tower will be standing straight up, without any lean to one side. To check this, you’ll need a level placed against the side of the tower. This tool will provide a clear indication of whether the tower is vertical.
Once the level is positioned, it’s time to loosen the Mobile Column Lift For Sale Oceanside CA anchor bolts that were tightened earlier. This may feel counterintuitive, but loosening the bolts is necessary to make the adjustments. Carefully insert the shims between the base of the tower and the concrete until the tower is in perfect alignment, ensuring that it is perpendicular to the ground.
Our Clients Include: