The use of shims here is crucial, as it helps maintain the correct position of the tower. When the tower is plumb, with no tilt or angle, retighten the anchor bolts to lock the tower into place. At this point, the adhesive should be sufficiently cured, the tower should be secured and aligned correctly, and the setup will be ready for the next phase of the installation process.

Now, at this stage, many first-time installers might mistakenly assume that it’s time to proceed with anchoring the second tower. However, this is not the next step. Instead, you should focus on fully assembling and installing the overhead bar. This task is essential before moving on to the second tower. The overhead bar is a critical component of the lift system, and its installation needs to be done in the correct order to ensure smooth operation. The first step in this process is to attach the wiring for the limit switch, which is responsible for controlling the operation of the lift. You will need to connect the wiring properly to ensure that the limit switch can perform its function when required.

Next, you’ll need to bolt the limit switch securely in place. This is important because the Mobile Column Lift For Sale Oceanside CA limit switch will be part of the system that halts the lift’s operation at certain points. Alongside the limit switch, you will also need to install the bracketry that holds the overhead shutoff bar. This shutoff bar is a crucial safety feature that ensures the lift is powered down when it reaches the predetermined point. After securing the brackets, the overhead shutoff bar itself must be installed. The final task for this part of the process is to secure the limit switch arm. This arm must be positioned so that when the shutoff bar is raised, the limit switch opens, cutting off the power to the lift. This safety mechanism ensures that the lift operates within safe parameters.

Once the Mobile Column Lift For Sale Oceanside CA shutoff bar and limit switch are installed, two people will need to work together to carry the overhead bar up using ladders. This step requires careful coordination to avoid accidents and to position the bar correctly. Once in place, the bar should be bolted securely to the structure, completing the overhead bar installation. This step is crucial because the overhead bar is a key part of the lift’s mechanism, and it must be installed correctly before the second tower can be anchored and the system can proceed to the next stage.

With the Mobile Column Lift For Sale Oceanside CA overhead bar installed and the first tower securely anchored to the concrete, attention must now turn to the second tower. The next task is to plumb the second tower and anchor it to the concrete. At this stage, it’s important to shift your focus from the earlier measurements concerning the spacing between the towers. While it’s essential to follow the manual for tower spacing, the priority now is ensuring that the towers are plumb, meaning they are perfectly vertical. This is more important than adhering strictly to the Mobile Column Lift For Sale Oceanside CA spacing measurements. To achieve this, place the level against the side of the second tower. Use a hammer to gently tap the base of the tower to adjust its position, either moving it inward or outward, until it is perfectly perpendicular to the ground. Even if the spacing changes slightly, such as from 138 inches to 137.5 inches, it is far more important that the second tower is plumb than that the towers are exactly as spaced in the manual. Once the second tower is aligned properly, repeat the process of securing it to the concrete using anchor bolts.

The next step involves the installation of the power unit, which is a vital component of the lift system. This task is best performed with the assistance of two people. The power unit is heavy and bulky, and attempting to install it alone can lead to injury or damage. By having two people, you can ensure that the power unit is lifted and positioned without risk. Prior to hanging the power unit, it’s advisable to pre-install the top two hanging bolts. These bolts will allow you to easily hang the power unit onto the mount on the tower, avoiding the need to balance the unit while trying to install the bolts. With the bolts in place, the power unit can be lifted into position, and once it’s hanging securely, the bolts should be tightened to ensure it is firmly attached to the mount.

After the power unit is secured, the next phase involves installing the Mobile Column Lift For Sale Oceanside CA hydraulic lines, hydraulic fittings, and the wire for the safety shutoff switch. The hydraulic lines must be routed according to the manual, ensuring they follow the correct path as shown in the provided diagram. These lines should be connected to the appropriate fittings, either flare fittings or Mobile Column Lift For Sale Oceanside CA o-ring fittings, as required by the system. It’s important to note that no thread sealant is necessary for these fittings, as they are designed to form a tight seal without additional sealing materials. As you work with the hydraulic lines, take care to avoid any tangling or bunching. You can use zip ties to secure any excess length of hydraulic line at the top of the lift. This will help prevent the lines from interfering with the carriage as it moves up and down inside the towers.

In addition to the Mobile Column Lift For Sale Oceanside CA hydraulic lines, the wire for the safety shutoff switch needs to be routed down to the power unit. The wire should follow the same path as the hydraulic lines to maintain organization and prevent tangling. This step completes the installation of the hydraulic lines and safety wiring. However, there is one additional tip that is crucial when installing the Tee fitting into the tower. When you insert the Tee fitting, it is important to adjust it so that as little of the fitting as possible protrudes inside the tower.